cboState => state or State (prime example of changing control types what about lstState or rdoState - they should all have the same name because your code is not concerned about the type of control,rather the state the user selected).How will you decide which prefix to use for the custom controls? Instead of focusing on the type of control, your code should be concerned with what information is contained in it. You may make your own WebUserControl, or you may purchase a set of third party controls. It is fairly easy to come up with prefixes for the standard controls, but new controls are being developed every day.When you are concerned with the type of the control, you start to depend on certain functionalities and you break encapsulation - you should be able to easily swap controls without changing much or any code. Your code should be more concerned with the content of the control and less with what type of control it is.Type of control may change from textbox to listbox, then all associated code will have to be fixed (noted earlier).Since UI controls are ultimately variables used in code, they should follow the same convention as any other variable - no hungarian notation prefix. Microsoft provides guidance in general for OO naming conventions, but not specifically for naming UI controls. Naming it "Control1" would be too confusing because it could be any number of controls. #types time string enum string enum string enum string string string string int interval string stringĠ.000000 - NetControl::MESSAGE - activating plugin with priority 0 - Debug-All 0.000000 - NetControl::MESSAGE - activation finished - Debug-All 0.000000 - NetControl::MESSAGE - plugin initialization done - 1427726759.303199 2 NetControl::RULE ADD NetControl::REQUESTED NetControl::DROP NetControl::FORWARD NetControl::ADDRESS 192.168.56.1/32 - 0 600.000000 ACTION_DROP: T Debug-All 1427726759.303199 2 NetControl::RULE ADD NetControl::SUCCEEDED NetControl::DROP NetControl::FORWARD NetControl::ADDRESS 192.168.56.1/32 - 0 600.The reason Visual Studio adds "TextBox1" when you add it to the page is because Microsoft has no way of knowing how you intend to use it. #fields ts rule_id category cmd state action target entity_type entity mod msg priority expire location plugin The debug plugin can be initialized as follows:Įvent NetControl::init (), _added=F] $ cat netcontrol.log The NetControl::activate function after the plugin instance has been This plugin outputs all actions that are taken to the standardīackends should be initialized in the NetControl::init event, calling For our examples, we will just use the debug plugin toĬreate a backend. You will need at least one active backend before youĬan use NetControl. As mentionedĪbove, NetControl uses backends to communicate with the external devices that In this section, we will introduce the high level NetControl API. NetControl API ¶ High-level NetControl API ¶ Thisĭocument will show how to write plugins in The backends are implemented as Zeek scripts using a plugin based API an exampleįor this is base/frameworks/netcontrol/plugins/broker.zeek. Success, failure and timeouts) back to the user scripts. Tracks rules throughout their entire lifecycle and reports the status (like To communicate with a single hard- or software device. Sends the rule to one or several of its backends. After a rule has been added to the NetControl framework, NetControl NetControl::drop_address function, or a lower level rule The NetControl framework supports a number of high-level calls, like the Hardware or software device), that is used to implement the commands. (which use the Zeek event engine) and the network device (which can either be a The basic architecture of the NetControl framework is shown in the figure above.Ĭonceptually, the NetControl framework sits between the user provided scripts NetControl architecture (click to enlarge). It can be used in practice, it might be worthwhile to take a look at This document gives an overview of how to use the NetControlįramework in different scenarios to get a better understanding of how Response and hides the complexity of heterogeneous network equipmentīehind a simple task-oriented API, which is easily usable via Zeek NetControl framework provides a flexible, unified interface for active Or soft- and hardware firewalls using the NetControl framework. Zeek can connect with network devices like, for example, switches
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |